Collab Mapping #01 Phase 1/3

[papercoffee]

It is not that I have troubles ...I have build a long funnel downward (it looked not bad) and suddenly comes this error message and the UEd closed without saving anything...

[editor Dave]

Check if the map still runs fine in the wire frame mode. If it does there are a two possiblities (from my experience):
1. Your light radii are too big. At first, rebuild lighting only, when this doesn't help reduce the radii to 20 (Check coronas, too).
2. MyLevel got destroyed somehow. Some textures got overwritten and now can't look at them anymore (ingame you see very strange textures but it runs). Then you can't even open the textures in MyLevel. That would be bad because only deleting the brushes would help...

[--=PsyXandeR=--]

My floating crates bug still needs to be fixed, I think

@Alex: Good, finally you also make a part^^. Maybe you can (try to) add a "replace me" brush in direction of editor dave temple part?

Won't it hurt the flow of the map though? In order to connect it to Dave's temple, you will have to make long hallway... unless you guys edit your parts and add some more REPLACEME cubes.

[Renegade]

GAAAAAAAAHHHH DAMN YOU "Protection fault" ...ok my part is not totally gone but ...you know what I feel right now, do you guys?

Were you Vertex Editing? That's usually when that happens to me. If two vertices are on the same point on the grid, bad things happen.

[Creavion]

GAAAAAAAAHHHH DAMN YOU "Protection fault" ...ok my part is not totally gone but ...you know what I feel right now, do you guys?

Were you Vertex Editing? That's usually when that happens to me. If two vertices are on the same point on the grid, bad things happen.

If Renegade should be right, I would like to kick your butt paper, use the well known rpg rule: "Save early, saven often"

[Myth]

You should bind mouseleft to quicksave and mouseright to quickload, just in case.

[Filipe]

And what does that means, are you going to do one again?

[[did]Madis]

GAAAAAAAAHHHH DAMN YOU "Protection fault" ...ok my part is not totally gone but ...you know what I feel right now, do you guys?

Were you Vertex Editing? That's usually when that happens to me. If two vertices are on the same point on the grid, bad things happen.

If Renegade should be right, I would like to kick your butt paper, use the well known rpg rule: "Save early, saven often"

I recently discovered UnrealED also has an autosave feature but that tends to corrupt my groups :O

[Renegade]

Progress anyone? I've got a week off classes so I have time to build a couple connector sections if needed. I just don't know who has what. I think at this point we should focus on "closing up" the map. That is, unless most of you want it bigger.

[--=PsyXandeR=--]

Have to work on lighting yet but thats pretty final. It is rather low poly as well, never goes above 190...

[Renegade]

Have to work on lighting yet but thats pretty final. It is rather low poly as well, never goes above 190...

Looks good. Everythings nice and trimmed I'm guessing glowing water/lava/slime is going under the ramp.

[Creavion]

Good start Alex, but I am just glad you also contribute something.

BTW: Could my floating crate bug plz be fixed?

[papercoffee]

Almost finished ....
Only need to put some pipes in the lava ...so my next part will be the Generator of the facility but first I finish this room.

[Filipe]

good! but, those stairs are strange

[Renegade]

good! but, those stairs are strange

Agreed. The floor looks grate. (haha?)
However, I would've made those "stairs" ramps or metal slats.